Raymond Mill Installation And Repair Of Good Sense

Raymond Mill Installation And Maintenance Of Good Judgment
Raymond Mill primary structure:
Raymond Mill mainly because of the number, analyzers, blower, finished cyclone, cyclone dust and atmosphere pipe. Among them, the host through the rack, inlet volute, knife, roller, milling band, cover structure. Swimming to be able to meet up with the needs of users, extremely solid device frame design, therefore, laying the foundation for regular removal gear isn’t just to the product on a hard flat surface are true and, if fixed installation, buckle machine, the very best struck concrete basis. Set up, please relate to installation diagram below. Added stability first, and a fixed number, and install the fan and linking duct, also cyclone. Can be used between your flange asbestos rope, rubber or foam seal, and then use alkyd white Houqi (commonly known as lead oil), strict sealing to do the job to prevent leakage of manufacturing.
Raymond Mill Operating Principle:
Work, should crush the materials through the hopper to the machine casing to join the medial side of machine, count on the number plum holding roller product racks, the change across the vertical axis, while its rotation, the rotation of centrifugal force, milling roll-out swinging, squeezed regarding milling band, the shovel knife to work the material amongst the roller and grinding ring, due to the rolling roller compacted to achieve the intent behind smashing.
Raymond Mill winnowing process:
After grinding the material, fans will likely be blown in the White case, the blowing powder, put into the grinding chamber through the top of the analyzer for sorting, good through coarse material to the grinding raymond mill chamber and re-grinding, compliant using fineness airflow in to the cyclone enthusiast, gathered and discharged through a dust socket, is finished. Airflow from the top of a big cyclone collector pipe back to the return environment lover, atmosphere duct is circular, plus in the circulation under negative stress, circulation air duct to improve ventilation between your number partly by the exhaust lover and exhaust pipeline in to the little cyclone enthusiast device, for purification.
Raymond mill use and maintenance of common sense:

1. The plane except the top the sliding bearing spindle, the other transmission parts for moving bearings, lubrication must for that reason maintain great operating problem, usually it’ll harm the bearings and shorten life. Repair is as uses: spindle oil time for you to class time, but must observe that the cup oil reduction or loss in oil just isn’t also sluggish, they should straight away clean the oil station, plus 50 # device oil, oil glass top position into the spindle, spindle base bearing, roller bearing axle with grease weapon filling each course 3 # lithium oil once every six months aside bearing analyzer washed as soon as, include somewhat 3 # lithium based grease, lithium plus fan-bearing area oil.
2. Non-metal block in to the device, otherwise it’s going to damage the milling roller and milling ring, and even center hanger.
3. The feeding is uniform, maybe not instantly much less dismissed. Extortionate feeding blocked duct will certainly reduce the yield, an easy task to burn out the motor, feeding not enough will impact production. Feed size: tough products significantly less than 15 mm in diameter, preferably, soft material for 20 mm diameter, non-bulk product included with the equipment.
4. Air volume control: the consumption pipe is located regarding blower air amount control device, usually available to the utmost position, relating to fineness, yield calls for a suitable adjustment. Situated on the fatigue pipeline socket fatigue valve, transmitted to the feed orifice is no dust emitted. Air volume is small, thin large. It should be mentioned, the wind is just too little, the host is not difficult duct below the deposit material, please adjust.
5. good adjustment, in line with the size of the materials, hardness, moisture content, the percentage various level of processing vary thickness, are modified at the top of the analyzer, high-speed, fineness, reasonable speed, low fineness. Improve fineness, the production are paid down accordingly, in case it is mainly the fan speed when debugging, an individual can flexibly.
6. Ring roller raymond mill scrap the limit, the minimum staying wall surface thickness of for around 10mm.
7. avoid, stop feeding, the system nonetheless consistently run, continue steadily to make recurring abrasive grinding, about a moment, turn off the key engine plus the motor analyzer, stop grinding work, after which stop the lover engine to blowing off the powder residue.

If you’d like to learn more about various other milling mill and crusher, be sure to get in touch with me.

Get A Hold Of Much More Hostels Articles